Market · Southeast Asia
Yingfei Entrance Door for Southeast Asia
The Yingfei Offset-Hinge Cast-Aluminium Entrance Door is configured here for Southeast Asia. The figures below are the published catalogue specification of the series; the market section covers what projects in Southeast Asia add to it. Send the opening schedule and the glazing you want, and the quotation comes back with the dimensional pack.
Yingfei Offset-Hinge Cast-Aluminium Entrance Door · Southeast Asia
Yingfei Offset-Hinge Cast-Aluminium Entrance Door
An offset pivot turns the leaf clear of the reveal, paired with a sculpted cast-aluminium art face. The complete configuration, glass options and finish list are on the door series page.
- Operation
- Offset-hinge swing, pivot inboard of the leaf edge
- Opening angle (catalogue)
- Large angle, close to 180 degrees, opening both ways
- Space
- Core areas inside and outside the opening stay clear
- Leaf face
- Cast-aluminium art face · marble face · slim glazing
- Frame
- Aluminium, per the catalogue scenes
- Structural build
- Aviation-grade aluminium plate · 1.0 mm steel plate · B1 flame-retardant board · PA66 insulation strip · automotive-grade sealing strip
- Durability (catalogue)
- Balanced pivot load, reduced sag and less hardware wear
- Hardware
- L8 face lock (palmar-vein option) · N6 fingerprint lock · F3 to F6 embedded locks
- Finishes
- Confirmed against the catalogue and samples on request
Engineering
Offset pivot, clear floorThe leaf turns on an axis inboard of its edge, so the core areas inside and outside the opening stay free and a tight plan keeps its floor in use.
Nearly 180 degrees, both waysThe catalogue gives the leaf a large opening angle close to 180 degrees and movement in both directions, so bulky items and several people pass without a hinge limit.
Cast-aluminium art faceSeveral leaves carry a sculpted cast-aluminium face set into the leaf, drawn in bronze, stone and dark tones, with the pivot hardware kept out of the closed face.
Balanced load, longer lifeThe catalogue says the pivot spreads and balances the load, which reduces sag and deformation of the leaf and cuts wear on the hardware parts.
Heat, humidity and salt air
Southeast Asian sites push three things at aluminium: sustained heat, high humidity and, on the coast, salt spray. The finish carries the corrosion load, which is why fluorocarbon and powder lines are the standard shortlist for coastal work, with EPDM sealing and open self-cleaning drainage handling the moisture inside the section.
Glazing is specified per project: single glass where cooling load is the driver, insulating units where comfort is. The build-up comes back on the quotation against your climate and the budget line for the envelope.
Ports and logistics for the region
The main ports in the region are covered by standard export packing: modules travel upright, edge-protected, in 20 ft or 40 ft containers, and the loading plan for your opening mix ships with the quotation.
Transit times vary by origin port and destination, so they are confirmed per shipment rather than quoted from a fixed table.
Reference projects in comparable climates
villa · day scene
Tropical house, deep roof overhang
Deep roof overhangs shade the sliding doors and keep the terrace usable through the wet season.
hotel · day scene
Resort hotel, pool frontage
Low-rise blocks set behind an infinity pool, with framed glazing opening the ground floor to the deck.
apartment · day scene
Apartments, recessed balconies
White volumes with deep recessed balconies and vertical sunshades cut the direct sun before it reaches the glass.
FAQ
Frequently asked
Which finishes hold up in coastal Southeast Asia?
Fluorocarbon and anodised lines are the standard shortlist against salt spray. RAL matching and two-tone exterior/interior combinations are available on request.
Do you ship to the Philippines and Malaysia?
Yes. Modules ship to ports across the region in export-standard containers, and the loading plan with the transit confirmation comes with the quotation.
What is the Yingfei offset-hinge door?
It is the offset-hinge entrance door of the AURORA range, printed on catalogue pages 075 to 084. The leaf turns on a pivot set inboard of its edge, which the catalogue gives as the answer for narrow spaces and small apartments.
How is it different from a standard swing door?
The pivot sits inboard of the leaf edge and the leaf opens through a large angle, close to 180 degrees, in both directions, so the core areas inside and outside the opening stay clear. A standard side hinge sweeps the leaf across that floor.
Keep going
Series, market and range
Send your opening schedule
Series, glazing and finish come back as one quotation for Southeast Asia, with the full dimensional pack on PDF and CAD on request.