Market · Australia
Anyue Cast Entrance Door for Australia
The Anyue One-Piece Cast-Aluminium Entrance Door is configured here for Australia. The figures below are the published catalogue specification of the series; the market section covers what projects in Australia add to it. Send the opening schedule and the glazing you want, and the quotation comes back with the dimensional pack.
Anyue One-Piece Cast-Aluminium Entrance Door · Australia
Anyue One-Piece Cast-Aluminium Entrance Door
The one-door-one-scene line of the entrance range: a one-piece cast-aluminium face on a sealed thermal-break frame. The complete configuration, glass options and finish list are on the door series page.
- Opening
- Single leaf, with a secondary leaf or a fixed glass panel where shown
- Door style
- One-piece cast-aluminium face, one door one scene
- Structural build
- Aviation-grade aluminium plate · 1.0 mm steel plate · B1 flame-retardant board · thermal-break profile · automotive-grade sealing strip · PA66 insulation strip · aluminium or wooden backboard
- Leaf face
- One-piece cast aluminium · cast architectural relief · no joints
- Frame
- Aluminium with thermal-break profiles
- Glazing
- Fixed glass panel where the catalogue draws it
- Performance (catalogue ratings)
- Sound 5 · thermal 8 · water 8 · air 8 · wind 9
- Hardware
- L8 face lock (palmar-vein option) · N6 fingerprint lock · F3 to F6 embedded locks with motor linkage · H3 horizontal handle
- Finishes
- No catalogue colour card · confirmed against samples on request
Engineering
One-piece cast leafThe catalogue casts the leaf as one aluminium body with no joints, so the architectural relief runs unbroken across the face.
Cast-in reliefThe pattern is cast into the face rather than applied, and the mould leaves the natural grain the catalogue compares to stone, timber and bronze.
Differentiated thermal-break buildThe cast leaf sits on the thermal-break system the catalogue prints on page 043, from an aviation-grade aluminium plate and a 1.0 mm steel plate through B1 flame-retardant board, PA66 insulation strip and automotive-grade sealing strip to the aluminium or wooden backboard.
Smart-lock readyThe hardware pages list the L8 face lock with an optional palmar-vein function, the N6 fingerprint lock and the F3 to F6 embedded locks with motor linkage, plus the H3 horizontal handle.
What Australian spec writers check
The Australian regime is built on testing, not on brand claims. AS/NZS 1170.2 sets the regional wind-load classification, AS 2047 defines how window and door assemblies are tested against wind load, and AS 1288 classifies the glazing itself. A cyclone-rated specification must therefore state the zone class, the tested configuration and the glazing classification for the exact module size.
Adam Alux does not hold AS 2047 test certificates. Engineering against your zone and module schedule is confirmed at quotation, and a finished test window or door can be produced before the production run.
Shipping to Australia
Modules travel to the major Australian ports in export-standard containers, packed upright with edge protection. The container count for your schedule depends on frame depth and glass build-up, so the loading plan comes with the quotation.
Transit and port handling are confirmed per shipment. For coastal projects, the fluorocarbon and anodised finish lines are the standard shortlist against salt-air exposure.
Projects in Australia
villa · day scene
Coastal house, full-height glazing
A raised concrete deck and full-height glazing turn the elevation toward the water, under a deep shaded veranda.
apartment · day scene
Apartments, angled sunshades
Pale render with dark metal balcony bands and angled sunshades over floor-to-ceiling framed windows.
villa · day scene
Terrace house, glass rear extension
The original brick frontage stays intact, with a slim-profile aluminium and glass extension reading as a separate volume.
FAQ
Frequently asked
Do your aluminium windows and doors ship to Australia?
Yes. Modules ship to the major Australian ports in export-standard containers, with the loading plan for your schedule included in the quotation.
How do you handle cyclone zone specifications?
The zone class and the module schedule drive the specification. Engineering and glazing classification are confirmed at quotation against the AS 2047 and AS 1288 requirements, with a test unit available before production.
What is the Anyue one-piece cast-aluminium entrance door?
It is the one-door-one-scene line of the AURORA entrance range, printed from catalogue page 043 as section 045P, with eight pieces from M-001 to M-008. The leaf is cast as one aluminium body with no joints.
How is the cast face different from an applied panel?
The catalogue casts the piece in one pour and casts the architectural relief into the face rather than applying it, so the pattern runs unbroken and the mould leaves a natural grain.
Keep going
Series, market and range
Send your opening schedule
Series, glazing and finish come back as one quotation for Australia, with the full dimensional pack on PDF and CAD on request.